Accumeg™ Megasonic Cleaning Tanks & Systems

Accumeg Megasonic Cleaning Tank Systems Quartz Recirculating

Quartz Megasonic
Cleaning Tank

Overview

Accumeg™ megasonic cleaning technology has been shown to be an essential performance element in advanced cleaning applications. Combining over 40 years of industry know-how with some of the most reliable megasonic tank components available, IMTEC has designed a cleaning system for a wide-range of high-purity processes. The Accumeg is designed to provide continuous megasonic energy across the full width and depth of all the substrates in the process tank. This constant energy is the key to complete, fast, efficient megasonic cleaning and the elimination of particle reattachment.

Unlike other systems, which use “pulsed” megasonic transducer arrays in an attempt to achieve even, full coverage, the Accumeg megasonic transducer array covers the entire process load capacity of the tank without any of the energy loss associated with “shadowing” or “sequencing”.

Backed by our extensive 36 month warranty, IMTEC’s Accumeg series offers the reliability and productivity that ensures excellent uptime, minimum maintenance and the lowest cost of ownership.

Brochures

Accumeg™ Megasonic Cleaning EquipmentAccumeg™ Megasonic Mini System
Get QuoteImtec Distributors

Features

  • Reliable components, extensive 36 month warranty
  • Cassette & cassette-less designs for up to 300 mm wafers & larger substrates
  • Field replaceable transducer arrays
  • High watt density
  • Operates at 70°C+
Accumeg Megasonic Cleaning Tank Systems PVDF Quick Dump

PVDF Megasonic
Cleaning Tank

Accumeg PVDF Megasonic Process Tank with Quick Dump Rinse

PVDF Megasonic Tank with Quick Dump Rinse

Megasonic Cleaning Technology

“Gapless” Transducer – For better process uniformity in the tank, the piezoelectric crystals on the transducer should be installed as close together as possible. However, when each crystal is wired to the generator individually, they must be spaced at least 1mm apart to avoid arcing that shorts out the transducer.

IMTEC uses superior transducers with tightly matched crystals wired together in parallel. This means that there is a small potential difference between crystals and they can be placed close together- 0.1mm apart- without risk of shorting.

Megasonic Quick Dump Rinse Bath (QDR) – To quickly remove chemical and particulate from a bath after a process run, IMTEC developed and patented the QDR Accumeg. Rather than disturbing the bottom of the bath where the transducer is mounted, the IMTECsystem raises the walls of the bath, allowing the chemical to flow out evenly and rapidly, and without allowing any particulate settled at the bottom of the bath to re-attach to the substrate. This “tank lift” system maintains a clean environment and saves valuable processing time. To learn more about megasonics and how they can improve your process please visit the download tab for more resources.

Accumeg Megasonic Cleaning Tank Systems Energy Uniformity

Megasonic tank energy uniformity test with probe and robotics

Megasonic Cleaning vs. Ultrasonic Cleaning

As wafer structures become smaller and more complex, Ultrasonic energy is becoming increasingly undesirable in the Semiconductor market. The high cavitation energy produced in Ultrasonic cleaning can blow out sensitive structures and damage substrates. The gentler cleaning energy produced by Megasonic waves can dislodge particles without damaging sensitive devices.

In a sonic cleaning system, a transducer generates high frequency vibrations in a fluid medium. These high frequency vibrations, as described below, create a scrubbing action on a substrate uniquely suited to cleaning devices with crevices or blind holes such as semiconductors or memory disks

The transducer mounted on the outside of the tank produces high frequency waves that propagate through the fluid medium. Each point along the wave oscillates between a maximum and minimum pressure. When the pressure minimum is below the vapor pressure of the fluid medium, bubbles are formed in the fluid medium. When the pressure increases to maximum pressure, the bubbles implode, sending out an intense shockwave of energy as the fluid rushes in to fill the void left by the collapsed bubble. This energy is referred to as cavitation energy, and is well-suited for dislodging particles or contaminants from a substrate.

Many factors can affect the intensity of the cavitation energy in a sonic process, such as the surface tension of the fluid medium, or the distance of the substrate from the transducer. However, a critical factor is the frequency of the sonic waves. In a typical Ultrasonic cleaning process, the transducer emits a frequency of less than 100kHz. This lower frequency means that bubbles have a longer time to form and grow, creating more cavitation energy when they collapse. Megasonic processes utilize frequencies from 600-2000 kHz. These higher frequencies mean that bubbles have less time to grow and are smaller when they collapse, producing a proportionally smaller amount of cavitation energy.

Megasonic Quick Dump Recommendations

The purpose of the Accumeg quick dump process is to remove, or keep suspended, any trace ionic species and/or particulate contaminants carried over from prior process steps that are held in the fluid boundary layer surrounding the wafers. The QDR rinse sequence is also critical for cleaning the QDR process vessel walls and cassette. While there are many processes which benefit from megasonic quick dump enhancement, two representative processes are shown in the table below. Process A is typical of quick-dump rinse that follows a prior cool process (under 100°C), while Process B similarly describes a quick-dump rinse that follows a prior hot process (over 100°C). The following table presents the general requirements for these two typical processes. Following the Table of General Process Requirements, is a more detailed recommended process sequence for both A and B is given.

General Process Requirements

A

Time/Temp/Flow

Set points for Rinsing immediately following an under-100°C prior process

[Examples: Post SC1 (NH4OH+H2O2+DI H2O) or SC2 (HCL+H2O2+DI water) Cleans]
  1. Start with a fresh, ambient DI-water cascade overflow of approximately 30 seconds, turn the megasonic energy on, then insert wafer load. All following rinse cycles should be with cold DI water. Do a minimum of four dump, fill and spray cycles, ending in wafer-load withdrawal during an overflow with bottom fill only. 
  2. DI-water fill rate must be adequate to fill the process vessel within 40-60 seconds with a combination of top spray and bottom fill.The top spray should be approximately 30% of the total DI-water flow.
B
Time/Temp/Flow

Set points for Rinsing immediately following an   over-100°C prior process

[Examples: Post Hot Piranha (H2SO4+H2O2+DI water) or Hot Phosphoric (H3PO4) applications]
  1. Start with a fresh, hot DI-water cascade overflow of approximately 30 seconds, turn the megasonic energy on, then insert wafer load. Do a minimum of 5 to 8 dump, fill and spray cycles, ending in wafer-load withdrawal during an overflow with bottom fill only. (The exact number of cycles depends upon the severity of carried-over contamination).
  2. The DI-water temperature during the first two (2) rinse/dump cycles should be 65-70oC DI water. The subsequent cycles can be with ambient DI water.
  3. DI-water fill rate must be adequate to fill the process vessel within 40 to 60 seconds with a combination of top spray and bottom fill DI water. The top spray should be approximately 30% of the total DI-water flow.
C
Megasonic Power Requirements
  1. Megasonic power should only be applied when the transducer is completely covered by DI water to a depth of at least 6 mm. Failure to observe this procedure could result in the damage of the transducer voiding the warranty.
  2. The amount of megasonic power required depends upon a number of factors such as degree of contamination, wafer surface condition and water temperature. However, a middle initiating point around which to determine the best power set point is usually in the 1½ to 2 watts per cm2 of the transducer area.

A and B Processes: Recommended Flow Description

  1. Both processes commence by dumping the process vessel contents held over from last step of the prior batch (Step 15);
  2. The Megasonic Quick Dump process vessel is filled using top spray and bottom fill manifolds and is permitted to overflow for thirty (30) seconds;
  3. The top spray is turned off and the megasonic power is turned on;
  4. The wafer load is inserted;
  5. With the megasonic power on, the wafer load is held in the overflowing quick dump rinse process vessel for approximately five (5) seconds;
  6. DI-water top spray is turned on; (Note: the DI bottom fill remains on)
  7. The process vessel quick dump is activated;
  8. Megasonic is turned off; (Note: DI water remains on)
  9. Quick Dump closes after approximately four (4) seconds;
  10. Once the water-fill level is approximately 6 mm above the transducer, the megasonic power is turned on;
  11. With the megasonic power on, the process vessel continues to be filled by both the top spray and bottom fill;
  12. Once filled, the process vessel is allowed to overflow for approximately 5 seconds and then again dumps;
  13. The above megasonic-rinse sequence (Steps 8 through 12) is repeated for the minimum number of cycles recommended for the particular A or B process (See Recommended Process Parameters in preceding chart);
  14. In the last cycle, the process vessel does not dump but remains in overflow mode with the megasonic power and DI bottom fill on, and the DI top spray off, while the wafer load is removed from the QDR and proceeds to its next process step;
  15. Once the wafer load has been removed from the ACCUMEG Quick Dump Rinser, the megasonic power and DI-water fills are turned off (except for a trickle purge of approximately 4-6 L/hr which is required to remain on at all times). The system remains in this standby condition, ready for the beginning of the next cycle.

Megasonic Equipment Specifications

Megasonic Tank & Transducer Specifications

Model specific information is supplied with each system.

  • Megasonic Frequencies: 975 & 730 kHz (+/-25 kHz) model dependent
  • Tank Materials: Quartz, PVDF, or PFA
  • Megasonic Transducer Plate: 316L Electropolished or PFA PTFE coated Stainless
  • Megasonic Transducer Cables: 25 ohm PTFE jacketed, 5 meter length
  • Maximum operating temperature for Boundary layer system: 130°C*
  • Maximum operating temperature for direct systems: 70°C
  • Operating Voltage: 208-230 VAC +/- 10% single phase
  • Limited Warranty: 36 months
  • Applicable Standards: Meets all applicable CE directives, 3rd party certified

*Requires adequate boundary layer cooling to keep transducer at 80°c or less.

Megasonic Generator Specifications

Accumeg Megasonic Genrator
Model
Megasonic Generator
Rated Output Power
1200 Watts
Output Range
60~1200 Watts
Oscillation System
Crystal controlled synthesizer
Rating Power Supply
208-230Vac ±10%, 10A,
single phase 50 or 60Hz
Remote Control
RS-485 or Discrete I/O control
External Dimensions
(WxDxH in mm)
380 x 550 x 175
Weight
< 25kg
Operating Ambient Condition
5-40°C

*Not including connectors, fan, switches, and other projecting parts. legs are included in dimensions.